TY - JOUR
T1 - Experimental study on pool boiling heat transfer enhancement with micro/nanostructured surfaces
AU - Zhang, Yonghai
AU - Liu, Bin
AU - Liu, Yongchen
AU - Yang, Yang
AU - Wei, Jinjia
N1 - Publisher Copyright:
© 2019 by Begell House, Inc.
PY - 2019
Y1 - 2019
N2 - An experimental study of pool boiling heat transfer was conducted for two types of micro-pin-finned surfaces [stag-gered micro-pin-fins with dimensions of 30 × 30 × 60 µm3 (width × thickness × height, named PF30-60-60) and cylindrical micro-pin-fins with dimensions of 38 × 60 × 60 µm3 (diameter × pitch × height, named PF38-60-60)], a nanowire surface, and a TiO2 porous surface. The experimental conditions covered three different liquid subcoolings (15, 25, and 35 K), in which dielectric liquid FC-72 was used as the working fluid. Micro-pin-finned surfaces have strong liquid supply capacity and small flow resistance. Therefore, micro-pin-finned surfaces were observed to have much higher critical heat flux (CHF) than that of the smooth surface (Chip S). However, for the nanowire and TiO2 porous surfaces, their very small micro/nanostructures increased the liquid flow resistance and obstructed the liquid supplement. Therefore, their CHF enhancement was not obvious compared to that of Chip S. PF38-60-60 showed the best heat transfer performance, with over 120% increase in CHF compared to Chip S and the lowest superheat in the nucleate boiling heat transfer region. The micro/nanocavity diameter of the nanowire surface was consistent with the effective diameter of the nucleation sites. Therefore, an obvious increase in heat transfer coefficient was found. In contrast, the TiO2 porous surface did not improve the heat transfer coefficient significantly because the nanocavity diameter was too small and could not be effective in the nucleation sites.
AB - An experimental study of pool boiling heat transfer was conducted for two types of micro-pin-finned surfaces [stag-gered micro-pin-fins with dimensions of 30 × 30 × 60 µm3 (width × thickness × height, named PF30-60-60) and cylindrical micro-pin-fins with dimensions of 38 × 60 × 60 µm3 (diameter × pitch × height, named PF38-60-60)], a nanowire surface, and a TiO2 porous surface. The experimental conditions covered three different liquid subcoolings (15, 25, and 35 K), in which dielectric liquid FC-72 was used as the working fluid. Micro-pin-finned surfaces have strong liquid supply capacity and small flow resistance. Therefore, micro-pin-finned surfaces were observed to have much higher critical heat flux (CHF) than that of the smooth surface (Chip S). However, for the nanowire and TiO2 porous surfaces, their very small micro/nanostructures increased the liquid flow resistance and obstructed the liquid supplement. Therefore, their CHF enhancement was not obvious compared to that of Chip S. PF38-60-60 showed the best heat transfer performance, with over 120% increase in CHF compared to Chip S and the lowest superheat in the nucleate boiling heat transfer region. The micro/nanocavity diameter of the nanowire surface was consistent with the effective diameter of the nucleation sites. Therefore, an obvious increase in heat transfer coefficient was found. In contrast, the TiO2 porous surface did not improve the heat transfer coefficient significantly because the nanocavity diameter was too small and could not be effective in the nucleation sites.
KW - Enhanced heat transfer
KW - Micro-pin-fins
KW - Nanowire
KW - Pool boiling
KW - TiO porous surface
UR - https://www.scopus.com/pages/publications/85077982682
U2 - 10.1615/InterfacPhenomHeatTransfer.2019030616
DO - 10.1615/InterfacPhenomHeatTransfer.2019030616
M3 - 文章
AN - SCOPUS:85077982682
SN - 2169-2785
VL - 7
SP - 19
EP - 31
JO - Interfacial Phenomena and Heat Transfer
JF - Interfacial Phenomena and Heat Transfer
IS - 1
ER -